Official Supplier Data: South West Water • DWI & BS 7593 Standards
Water Hardness in TQ14
Official water quality verdict for outcode TQ14: classified as Soft Water (40 PPM), supplied and treated by South West Water across 4 sectors.
Rating: Soft Water40 PPM • 2.8° ClarkSupplier: South West Water-80% below UK average
Outcode Mean Hardness40 PPM2.8° Clark • Soft Water4.0°fH • 2.2°dH
Outcode TQ14 Household Water Quality Verdict & Practical Advice
Domestic tap water in outcode TQ14 is officially classified as soft water, averaging 40 PPM (mg/L CaCO₃) or 2.8° Clark, supplied and treated by South West Water across all 4 postcode sectors (660 postcodes). Readings range from 40 PPM (TQ14 0) to 40 PPM (TQ14 9) with consistent mineral levels throughout.
☕ Kettle & Tea Quality:
Naturally soft water leaves kettles clear of mineral furring. Your tea brews bright and clean with zero tea scum.
🚿 Skin & Bathing:
Gentle on sensitive skin and eczema-prone households. Soaps lather richly with small amounts of product.
🍽️ Appliances & Salt:
Dishwasher salt top-up is optional or minimal (setting H00 (No salt required)). Boilers operate at peak thermal efficiency without scale.
Local Installer Quote Network
Looking for Water Treatment & Heating Protection in TQ14 (40 PPM)?
Connect with certified local specialists for drinking water filtration and British Standard BS 7593 anti-corrosion boiler protection in South West Water.
Verified Against British Standard BS 7593
WRAS-Approved Filtration Systems
100% Free & No Obligation Quotes
vs. UK Benchmark-80% Softervs 200 PPM national average
Statistical distribution across all 4 postcode sectors and 660 delivery points under South West Water's catchment monitoring:
Analyzed Sectors4660 postcodes
PPM Spread (Min - Max)40 – 40Variance: 0 PPM
Predominant ZoneSoft Water0% hard/very hard
Regulating AuthoritySouth West WaterDWI Regulated Supply
Hydro Metric
Outcode TQ14 Level
UK National Reference
Regional Status
Mean Mineral Density
40 PPM (2.8 °Clark)
200 PPM (14.0 °Clark)
-80% below baseline
French & German Scale
4.0 °fH / 2.2 °dH
20.0 °fH / 11.2 °dH
European standard conversion
Catchment Uniformity
Uniform (Single primary source)
Regional blending standard
Single Water Zone
Dishwasher Salt Calibration
H00 (No salt required)
Bosch H03 / Beko Level 2
Salt optional
Regional Hydro-Geological Overview
Water Hardness Breakdown: Outcode TQ14
Serving 660 homes and businesses across outcode TQ14, mains tap water supplied by South West Water registers an average mineral density of 40 PPM (4.0°fH / 2.2°dH). Rated as soft water, local water hardness determines how well laundry detergents lather, the rate of scale accumulation in combi boilers, and whether sensitive skin or eczema flares up after showers.
Water hardness is remarkably consistent across all 4 sectors of TQ14, with readings holding steady at 40 PPM from TQ14 0 through to TQ14 9. This uniform profile means every household on the South West Water network in this zone shares the same appliance settings and kettle descaling routine.
Supplies across TQ14 are managed by South West Water through a balanced mix of lowland river abstraction and regional storage reservoirs. Water hardness fluctuates moderately between wet winter periods and dry summer months, averaging 40 PPM across all 660 local postcodes under strict Drinking Water Inspectorate (DWI) compliance.
Households across TQ14's 4 sectors enjoy extended appliance lifespans. Because water contains just 40 PPM of dissolved minerals, kettles remain clean without periodic acid descaling, and sensitive skin or eczema is far less prone to irritation caused by calcium mineral deposits.
Estimated Annual Household Financial Impact
Limescale & Appliance Operating Costs in Outcode TQ14
Based on 40 PPM mineral saturation (Soft Water), operating heating appliances across TQ14's 660 households carries distinct annual economic consequences:
Extra Combi Boiler Gas Cost£0 (Optimal heat transfer)
Tap water throughout outcode TQ14 is supplied from a unified distribution network managed by South West Water. With all 4 sectors presenting an identical mineral concentration of 40 PPM, households across all 660 postcodes share uniform limescale risk profiles and identical appliance salt calibrations (H00 (No salt required)).
Frequently Asked Questions: Water in Outcode TQ14
Q: What is the average water hardness in outcode TQ14?
Tap water across outcode TQ14 averages 40 PPM (mg/L), which equals 2.8° Clark, 4.0°fH, or 2.2°dH. It is officially classified as soft water water supplied by South West Water.
Q: Is water in TQ14 harder than the UK national average?
The UK baseline average is approximately 200 PPM. At 40 PPM, water in outcode TQ14 is 80% softer than the national benchmark.
Q: What dishwasher salt setting is recommended for TQ14?
For Bosch, Siemens, and Neff dishwashers in outcode TQ14 (40 PPM), the recommended softener setting is H00 (No salt required).
Q: Who manages the municipal water supply in outcode TQ14?
Public tap water infrastructure across all 4 sectors in outcode TQ14 is distributed and monitored by South West Water.
All Postcode Sectors in TQ14
Select a postcode sector below to view exact water softener salt settings, limescale protection guides, and appliance recommendations.