Official Supplier Data: South West Water • DWI & BS 7593 Standards
Water Hardness in PL23
Official water quality verdict for outcode PL23: classified as Soft Water (40 PPM), supplied and treated by South West Water across 1 sectors.
Rating: Soft Water40 PPM • 2.8° ClarkSupplier: South West Water-80% below UK average
Outcode Mean Hardness40 PPM2.8° Clark • Soft Water4.0°fH • 2.2°dH
Outcode PL23 Household Water Quality Verdict & Practical Advice
Domestic tap water in outcode PL23 is officially classified as soft water, averaging 40 PPM (mg/L CaCO₃) or 2.8° Clark, supplied and treated by South West Water across all 1 postcode sectors (171 postcodes). Readings range from 40 PPM (PL23 1) to 40 PPM (PL23 1) with consistent mineral levels throughout.
☕ Kettle & Tea Quality:
Naturally soft water leaves kettles clear of mineral furring. Your tea brews bright and clean with zero tea scum.
🚿 Skin & Bathing:
Gentle on sensitive skin and eczema-prone households. Soaps lather richly with small amounts of product.
🍽️ Appliances & Salt:
Dishwasher salt top-up is optional or minimal (setting H00 (No salt required)). Boilers operate at peak thermal efficiency without scale.
Local Installer Quote Network
Looking for Water Treatment & Heating Protection in PL23 (40 PPM)?
Connect with certified local specialists for drinking water filtration and British Standard BS 7593 anti-corrosion boiler protection in South West Water.
Verified Against British Standard BS 7593
WRAS-Approved Filtration Systems
100% Free & No Obligation Quotes
vs. UK Benchmark-80% Softervs 200 PPM national average
Statistical distribution across all 1 postcode sectors and 171 delivery points under South West Water's catchment monitoring:
Analyzed Sectors1171 postcodes
PPM Spread (Min - Max)40 – 40Variance: 0 PPM
Predominant ZoneSoft Water0% hard/very hard
Regulating AuthoritySouth West WaterDWI Regulated Supply
Hydro Metric
Outcode PL23 Level
UK National Reference
Regional Status
Mean Mineral Density
40 PPM (2.8 °Clark)
200 PPM (14.0 °Clark)
-80% below baseline
French & German Scale
4.0 °fH / 2.2 °dH
20.0 °fH / 11.2 °dH
European standard conversion
Catchment Uniformity
Uniform (Single primary source)
Regional blending standard
Single Water Zone
Dishwasher Salt Calibration
H00 (No salt required)
Bosch H03 / Beko Level 2
Salt optional
Regional Hydro-Geological Overview
Water Hardness Breakdown: Outcode PL23
Serving 171 homes and businesses across outcode PL23, mains tap water supplied by South West Water registers an average mineral density of 40 PPM (4.0°fH / 2.2°dH). Rated as soft water, local water hardness determines how well laundry detergents lather, the rate of scale accumulation in combi boilers, and whether sensitive skin or eczema flares up after showers.
Water hardness is remarkably consistent across all 1 sectors of PL23, with readings holding steady at 40 PPM from PL23 1 through to PL23 1. This uniform profile means every household on the South West Water network in this zone shares the same appliance settings and kettle descaling routine.
Supplies across PL23 are managed by South West Water through a balanced mix of lowland river abstraction and regional storage reservoirs. Water hardness fluctuates moderately between wet winter periods and dry summer months, averaging 40 PPM across all 171 local postcodes under strict Drinking Water Inspectorate (DWI) compliance.
Living with naturally soft water (40 PPM) in outcode PL23 offers welcome household benefits. Your kettle stays clean with virtually zero limescale buildup, tea brews clear without unsightly floating scum, and shower gels lather effortlessly. Combi boilers and immersion heaters maintain peak fuel efficiency (0% scale drag), and dishwasher salt top-up is optional or minimal (recommended setting: H00 (No salt required)).
Estimated Annual Household Financial Impact
Limescale & Appliance Operating Costs in Outcode PL23
Based on 40 PPM mineral saturation (Soft Water), operating heating appliances across PL23's 171 households carries distinct annual economic consequences:
Extra Combi Boiler Gas Cost£0 (Optimal heat transfer)
Tap water throughout outcode PL23 is supplied from a unified distribution network managed by South West Water. With sector PL23 1 presenting an identical mineral concentration of 40 PPM, households across all 171 postcodes share uniform limescale risk profiles and identical appliance salt calibrations (H00 (No salt required)).
Frequently Asked Questions: Water in Outcode PL23
Q: What is the average water hardness in outcode PL23?
Tap water across outcode PL23 averages 40 PPM (mg/L), which equals 2.8° Clark, 4.0°fH, or 2.2°dH. It is officially classified as soft water water supplied by South West Water.
Q: Is water in PL23 harder than the UK national average?
The UK baseline average is approximately 200 PPM. At 40 PPM, water in outcode PL23 is 80% softer than the national benchmark.
Q: What dishwasher salt setting is recommended for PL23?
For Bosch, Siemens, and Neff dishwashers in outcode PL23 (40 PPM), the recommended softener setting is H00 (No salt required).
Q: Who manages the municipal water supply in outcode PL23?
Public tap water infrastructure across all 1 sectors in outcode PL23 is distributed and monitored by South West Water.
All Postcode Sectors in PL23
Select a postcode sector below to view exact water softener salt settings, limescale protection guides, and appliance recommendations.