Official Supplier Data: Anglian Water • DWI & BS 7593 Standards
Water Hardness in CO2
Official water quality verdict for outcode CO2: classified as Very Hard Water (310 PPM), supplied and treated by Anglian Water across 4 sectors.
Rating: Very Hard Water310 PPM • 21.7° ClarkSupplier: Anglian Water+55% above UK average
Outcode Mean Hardness310 PPM21.7° Clark • Very Hard Water31.0°fH • 17.4°dH
Outcode CO2 Household Water Quality Verdict & Practical Advice
Domestic tap water in outcode CO2 is officially classified as very hard water, averaging 310 PPM (mg/L CaCO₃) or 21.7° Clark, supplied and treated by Anglian Water across all 4 postcode sectors (944 postcodes). Readings range from 310 PPM (CO2 0) to 310 PPM (CO2 9) with consistent mineral levels throughout.
☕ Kettle & Tea Quality:
Rapid limescale buildup in kettles with floating scum on your cuppa. Descale monthly using white vinegar or food-grade citric acid.
🚿 Skin & Bathing:
High calcium levels can aggravate dry skin & eczema sensitivity. Soap lathers less easily, often leaving a tight feeling after hot showers.
🍽️ Appliances & Salt:
Keep water softener salt topped up and calibrate dishwashers to H06 – H07 (Max salt). Protect combi boiler heat exchangers under BS 7593.
Local Installer Quote Network
Living in a Hard Water Zone (CO2 averages 310 PPM)? Compare Approved Local Installers
Get up to 3 free, no-obligation quotes from WRAS-approved water softener installers and heating engineers serving Anglian Water.
Verified Against British Standard BS 7593
WRAS-Approved Water Softeners
100% Free & No Obligation Quotes
vs. UK Benchmark+55% Hardervs 200 PPM national average
Tired of stubborn limescale buildup in your kettle or dealing with an unappetising film of scum on your morning cuppa? Tap water across all 4 postcode sectors in outcode CO2 (covering 944 homes) averages 310 PPM (21.7° Clark). Maintained and distributed by Anglian Water, this places the district firmly into the very hard water bracket—approximately 55% harder than the UK national baseline (200 PPM).
Water hardness is remarkably consistent across all 4 sectors of CO2, with readings holding steady at 310 PPM from CO2 0 through to CO2 9. This uniform profile means every household on the Anglian Water network in this zone shares the same appliance settings and kettle descaling routine.
The reason tap water in CO2 carries significant dissolved minerals lies in local geology. Anglian Water abstracts substantial water supplies from subterranean chalk and limestone aquifers. As rainwater percolates through deep calcium-rich rock strata over decades, it dissolves natural calcium carbonate. While entirely safe and wholesome under Drinking Water Inspectorate (DWI) standards, these minerals precipitate out when heated above 60°C, leaving stubborn limescale deposits on heating coils.
Hard water in CO2 (310 PPM) often causes a cloudy scum on hot drinks and makes soap harder to lather, aggravating dry skin and eczema sensitivity after hot baths. For appliances, ensure regular water softener salt top-ups and calibrate your dishwasher to H06 – H07 (Max salt) to avoid cloudy glassware, white streaks, and heating element burnout across all 944 postcodes.
Estimated Annual Household Financial Impact
Limescale & Appliance Operating Costs in Outcode CO2
Based on 310 PPM mineral saturation (Very Hard Water), operating heating appliances across CO2's 944 households carries distinct annual economic consequences:
Extra Combi Boiler Gas Cost£190 – £260
Thermal heating transfer resistance caused by 1mm–1.5mm calcium carbonate build-up on heat exchangers.
Dishwasher Salt Requirement14 – 18 kg
Essential ion-exchange resin bed regeneration salt required to avoid glass clouding and element burnout.
Heating Element Degradation18% – 25%+ thermal drag
-40% to -50% life reduction without water softening.
Tap water throughout outcode CO2 is supplied from a unified distribution network managed by Anglian Water. With all 4 sectors presenting an identical mineral concentration of 310 PPM, households across all 944 postcodes share uniform limescale risk profiles and identical appliance salt calibrations (H06 – H07 (Max salt)).
Frequently Asked Questions: Water in Outcode CO2
Q: What is the average water hardness in outcode CO2?
Tap water across outcode CO2 averages 310 PPM (mg/L), which equals 21.7° Clark, 31.0°fH, or 17.4°dH. It is officially classified as very hard water water supplied by Anglian Water.
Q: Is water in CO2 harder than the UK national average?
The UK baseline average is approximately 200 PPM. At 310 PPM, water in outcode CO2 is 55% harder than the national benchmark.
Q: What dishwasher salt setting is recommended for CO2?
For Bosch, Siemens, and Neff dishwashers in outcode CO2 (310 PPM), the recommended softener setting is H06 – H07 (Max salt).
Q: Who manages the municipal water supply in outcode CO2?
Public tap water infrastructure across all 4 sectors in outcode CO2 is distributed and monitored by Anglian Water.
All Postcode Sectors in CO2
Select a postcode sector below to view exact water softener salt settings, limescale protection guides, and appliance recommendations.